-
-
-
-
-
rnat
-
-
-
-
-
This content has been machine translated dynamically.
Dieser Inhalt ist eine maschinelle Übersetzung, die dynamisch erstellt wurde. (Haftungsausschluss)
Cet article a été traduit automatiquement de manière dynamique. (Clause de non responsabilité)
Este artículo lo ha traducido una máquina de forma dinámica. (Aviso legal)
此内容已经过机器动态翻译。 放弃
このコンテンツは動的に機械翻訳されています。免責事項
이 콘텐츠는 동적으로 기계 번역되었습니다. 책임 부인
Este texto foi traduzido automaticamente. (Aviso legal)
Questo contenuto è stato tradotto dinamicamente con traduzione automatica.(Esclusione di responsabilità))
This article has been machine translated.
Dieser Artikel wurde maschinell übersetzt. (Haftungsausschluss)
Ce article a été traduit automatiquement. (Clause de non responsabilité)
Este artículo ha sido traducido automáticamente. (Aviso legal)
この記事は機械翻訳されています.免責事項
이 기사는 기계 번역되었습니다.책임 부인
Este artigo foi traduzido automaticamente.(Aviso legal)
这篇文章已经过机器翻译.放弃
Questo articolo è stato tradotto automaticamente.(Esclusione di responsabilità))
Translation failed!
rnat
The following operations can be performed on “rnat”:
clear rnat
Removes an RNAT rule from the Citrix ADC.
Synopsis
clear rnat ((
Arguments
network The network address defined for the RNAT entry.
netmask The subnet mask for the network address.
aclname An extended ACL defined for the RNAT entry.
redirectPort The port number to which the packets are redirected.
natIP The NAT IP address defined for the RNAT entry.
td Integer value that uniquely identifies the traffic domain in which you want to configure the entity. If you do not specify an ID, the entity becomes part of the default traffic domain, which has an ID of 0. Minimum value: 0 Maximum value: 4094
ownerGroup The owner node group in a Cluster for this rnat rule. Default value: DEFAULT_NG
stat rnat
Display statistics for rnat sessions.
Synopsis
stat rnat [-detail] [-fullValues] [-ntimes |
full )] |
Arguments
detail Specifies detailed output (including more statistics). The output can be quite voluminous. Without this argument, the output will show only a summary.
fullValues Specifies that numbers and strings should be displayed in their full form. Without this option, long strings are shortened and large numbers are abbreviated
ntimes The number of times, in intervals of seven seconds, the statistics should be displayed. Default value: 1 Minimum value: 0
logFile The name of the log file to be used as input.
clearstats Clear the statsistics / counters
Possible values: basic, full
Output
Counters
Bytes Received (rnatRxBytes) Bytes received during RNAT sessions.
Bytes Sent (rnatTxBytes) Bytes sent during RNAT sessions.
Packets Received (rnatRxPkts) Packets received during RNAT sessions.
Packets Sent (rnatTxPkts) Packets sent during RNAT sessions.
Syn Sent (rnatTxSyn) Requests for connections sent during RNAT sessions.
Current RNAT sessions (rnatSessions) Currently active RNAT sessions.
Example
stat rnat
Related Commands
unset rnat
Use this command to modify the parameters of configured Reverse NAT on the system..Refer to the set rnat command for meanings of the arguments.
Synopsis
unset rnat ((
set rnat
Modifies parameters of an RNAT rule.
Synopsis
set rnat ((
Arguments
network IPv4 network address on whose traffic you want the Citrix ADC to do RNAT processing.
netmask Subnet mask associated with the network address.
natIP Any Citrix ADC-owned IPv4 address except the NSIP address. The Citrix ADC replaces the source IP addresses of server-generated packets with the IP address specified. The IP address must be a public Citrix ADC-owned IP address. If you specify multiple addresses for this field, NAT IP selection uses the round robin algorithm for each session. By specifying a range of IP addresses, you can specify all Citrix ADC-owned IP addresses, except the NSIP, that fall within the specified range.
td Integer value that uniquely identifies the traffic domain in which you want to configure the entity. If you do not specify an ID, the entity becomes part of the default traffic domain, which has an ID of 0. Minimum value: 0 Maximum value: 4094
aclname Name of any configured extended ACL whose action is ALLOW. The condition specified in the extended ACL rule isused as the condition for the RNAT6 rule.
redirectPort The port number to which the packets are redirected. Minimum value: 1 Maximum value: 65535
natIP The NAT IP(s) assigned to the RNAT.
srcippersistency Enables the Citrix ADC to use the same NAT IP address for all RNAT sessions initiated from a particular server.
Possible values: ENABLED, DISABLED Default value: DISABLED
useproxyport Enable source port proxying, which enables the Citrix ADC to use the RNAT ips using proxied source port.
Possible values: ENABLED, DISABLED Default value: ENABLED
ownerGroup The owner node group in a Cluster for this rnat rule. Default value: DEFAULT_NG
connfailover Synchronize all connection-related information for the RNAT sessions with the secondary ADC in a high availability (HA) pair.
Possible values: ENABLED, DISABLED Default value: DISABLED
show rnat
Display the Reverse NAT configuration.
Synopsis
show rnat
Arguments
Output
network The network address.
netmask Subnet mask associated with the network address.
td Integer value that uniquely identifies the traffic domain in which you want to configure the entity. If you do not specify an ID, the entity becomes part of the default traffic domain, which has an ID of 0.
natIP Nat IP Address.
aclname Name of any configured extended ACL whose action is ALLOW. The condition specified in the extended ACL rule isused as the condition for the RNAT6 rule.
redirectPort The port number to which the packets are redirected.
srcippersistency Enables the Citrix ADC to use the same NAT IP address for all RNAT sessions initiated from a particular server.
useproxyport Enable source port proxying, which enables the Citrix ADC to use the RNAT ips using proxied source port.
cfgflags This contains the flags for RNAT in DB
ownerGroup The owner node group in a Cluster for this rnat rule.
connfailover Synchronize all connection-related information for the RNAT sessions with the secondary ADC in a high availability (HA) pair.
devno count stateflag
In this article
This Preview product documentation is Citrix Confidential.
You agree to hold this documentation confidential pursuant to the terms of your Citrix Beta/Tech Preview Agreement.
The development, release and timing of any features or functionality described in the Preview documentation remains at our sole discretion and are subject to change without notice or consultation.
The documentation is for informational purposes only and is not a commitment, promise or legal obligation to deliver any material, code or functionality and should not be relied upon in making Citrix product purchase decisions.
If you do not agree, select I DO NOT AGREE to exit.