ADC NITRO APIs

Interface

August 17, 2023

Contributed by:

Configuration for interface resource.

Properties

(click to see Operations )

Name	Data Type	Permissions	Description
id		Read-write	Interface number, in C/U format, where C can take one of the following values 0 - Indicates a management interface. 1 - Indicates a 1 Gbps port. 10 - Indicates a 10 Gbps port. LA - Indicates a link aggregation port. LO - Indicates a loop back port. U is a unique integer for representing an interface in a particular port group.
speed		Read-write	Ethernet speed of the interface, in Mbps. Notes If you set the speed as AUTO, the Citrix ADC attempts to auto-negotiate or auto-sense the link speed of the interface when it is UP. You must enable auto negotiation on the interface. If you set a speed other than AUTO, you must specify the same speed for the peer network device. Mismatched speed and duplex settings between the peer devices of a link lead to link errors, packet loss, and other errors. Some interfaces do not support certain speeds. If you specify an unsupported speed, an error message appears. Default value: AUTO Possible values = AUTO, 10, 100, 1000, 10000, 25000, 40000, 50000, 100000
duplex		Read-write	The duplex mode for the interface. Notes:* If you set the duplex mode to AUTO, the Citrix ADC attempts to auto-negotiate the duplex mode of the interface when it is UP. You must enable auto negotiation on the interface. If you set a duplex mode other than AUTO, you must specify the same duplex mode for the peer network device. Mismatched speed and duplex settings between the peer devices of a link lead to link errors, packet loss, and other errors. Default value: AUTO Possible values = AUTO, HALF, FULL
flowctl		Read-write	802.3x flow control setting for the interface. The 802.3x specification does not define flow control for 10 Mbps and 100 Mbps speeds, but if a Gigabit Ethernet interface operates at those speeds, the flow control settings can be applied. The flow control setting that is finally applied to an interface depends on auto-negotiation. With the ON option, the peer negotiates the flow control, but the appliance then forces two-way flow control for the interface. Default value: OFF Possible values = OFF, RX, TX, RXTX, ON
autoneg		Read-write	Auto-negotiation state of the interface. With the ENABLED setting, the Citrix ADC auto-negotiates the speed and duplex settings with the peer network device on the link. The Citrix ADC appliance auto-negotiates the settings of only those parameters (speed or duplex mode) for which the value is set as AUTO. Default value: NSA_DVC_AUTONEG_ON Possible values = DISABLED, ENABLED
hamonitor		Read-write	In a High Availability (HA) configuration, monitor the interface for failure events. In an HA configuration, an interface that has HA MON enabled and is not bound to any Failover Interface Set (FIS), is a critical interface. Failure or disabling of any critical interface triggers HA failover. Default value: ON Possible values = ON, OFF
haheartbeat		Read-write	In a High Availability (HA) or Cluster configuration, configure the interface for sending heartbeats. In an HA or Cluster configuration, an interface that has HA Heartbeat disabled should not send the heartbeats. Default value: ON Possible values = OFF, ON
mtu		Read-write	The maximum transmission unit (MTU) is the largest packet size, measured in bytes excluding 14 bytes ethernet header and 4 bytes crc, that can be transmitted and received by this interface. Default value of MTU is 1500 on all the interface of Citrix ADC any value configured more than 1500 on the interface will make the interface as jumbo enabled. In case of cluster backplane interface MTU value will be changed to 1514 by default, user has to change the backplane interface value to maximum mtu configured on any of the interface in cluster system plus 14 bytes more for backplane interface if Jumbo is enabled on any of the interface in a cluster system. Changing the backplane will bring back the MTU of backplane interface to default value of 1500. If a channel is configured as backplane then the same holds true for channel as well as member interfaces. Default value: 1500 Minimum value = 1500 Maximum value = 9216
ringsize		Read-write	The receive ringsize of the interface. A higher number provides more number of buffers in handling incoming traffic. Default value: 2048 Minimum value = 512 Maximum value = 16384
ringtype		Read-write	The receive ringtype of the interface (Fixed or Elastic). A fixed ring type pre-allocates configured number of buffers irrespective of traffic rate. In contrast, an elastic ring, expands and shrinks based on incoming traffic rate. Default value: Elastic Possible values = Elastic, Fixed
tagall		Read-write	Add a four-byte 802.1q tag to every packet sent on this interface. The ON setting applies the tag for this interface’s native VLAN. OFF applies the tag for all VLANs other than the native VLAN. Default value: OFF Possible values = ON, OFF
trunk		Read-write	This argument is deprecated by tagall. Default value: OFF Possible values = ON, OFF
trunkmode		Read-write	Accept and send 802.1q VLAN tagged packets, based on Allowed Vlan List of this interface. Default value: OFF Possible values = ON, OFF
trunkallowedvlan	<String[]>	Read-write	VLAN ID or range of VLAN IDs will be allowed on this trunk interface. In the command line interface, separate the range with a hyphen. For example: 40-90. Minimum length = 1 Maximum length = 4094
lacpmode		Read-write	Bind the interface to a LA channel created by the Link Aggregation control protocol (LACP). Available settings function as follows Active - The LA channel port of the Citrix ADC generates LACPDU messages on a regular basis, regardless of any need expressed by its peer device to receive them. Passive - The LA channel port of the Citrix ADC does not transmit LACPDU messages unless the peer device port is in the active mode. That is, the port does not speak unless spoken to. Disabled - Unbinds the interface from the LA channel. If this is the only interface in the LA channel, the LA channel is removed. Default value: DISABLED Possible values = DISABLED, ACTIVE, PASSIVE
lacpkey		Read-write	Integer identifying the LACP LA channel to which the interface is to be bound. For an LA channel of the Citrix ADC, this digit specifies the variable x of an LA channel in LA/x notation, where x can range from 1 to 8. For example, if you specify 3 as the LACP key for an LA channel, the interface is bound to the LA channel LA/3. For an LA channel of a cluster configuration, this digit specifies the variable y of a cluster LA channel in CLA/(y-4) notation, where y can range from 5 to 8. For example, if you specify 6 as the LACP key for a cluster LA channel, the interface is bound to the cluster LA channel CLA/2. Minimum value = 1 Maximum value = 8
lagtype		Read-write	Type of entity (Citrix ADC or cluster configuration) for which to create the channel. Default value: NODE Possible values = NODE, CLUSTER
lacppriority		Read-write	LACP port priority, expressed as an integer. The lower the number, the higher the priority. The Citrix ADC limits the number of interfaces in an LA channel to sixteen. Default value: 32768 Minimum value = 1 Maximum value = 65535
lacptimeout		Read-write	Interval at which the Citrix ADC sends LACPDU messages to the peer device on the LA channel. Available settings function as follows LONG - 30 seconds. SHORT - 1 second. Default value: NSA_LACP_TIMEOUT_LONG Possible values = LONG, SHORT
ifalias		Read-write	Alias name for the interface. Used only to enhance readability. To perform any operations, you have to specify the interface ID. Default value: “ “ Maximum length = 31
throughput		Read-write	Low threshold value for the throughput of the interface, in Mbps. In an HA configuration, failover is triggered if the interface has HA MON enabled and the throughput is below the specified the threshold. Minimum value = 0 Maximum value = 160000
linkredundancy		Read-write	Link Redundancy for Cluster LAG. Default value: OFF Possible values = ON, OFF
bandwidthhigh		Read-write	High threshold value for the bandwidth usage of the interface, in Mbps. The Citrix ADC generates an SNMP trap message when the bandwidth usage of the interface is greater than or equal to the specified high threshold value. Minimum value = 0 Maximum value = 160000
bandwidthnormal		Read-write	Normal threshold value for the bandwidth usage of the interface, in Mbps. When the bandwidth usage of the interface becomes less than or equal to the specified normal threshold after exceeding the high threshold, the Citrix ADC generates an SNMP trap message to indicate that the bandwidth usage has returned to normal. Minimum value = 0 Maximum value = 160000
lldpmode		Read-write	Link Layer Discovery Protocol (LLDP) mode for an interface. The resultant LLDP mode of an interface depends on the LLDP mode configured at the global and the interface levels. Possible values = NONE, TRANSMITTER, RECEIVER, TRANSCEIVER
lrsetpriority		Read-write	LRSET port priority, expressed as an integer ranging from 1 to 1024. The highest priority is 1. The Citrix ADC limits the number of interfaces in an LRSET to 8. Within a LRSET the highest LR Priority Interface is considered as the first candidate for the Active interface, if the interface is UP. Default value: 1024 Minimum value = 1 Maximum value = 1024
devicename		Read-only	Name of the interface.
unit		Read-only	Unit number for this interface, signifying the sequence number in which this interface is discovered on this Citrix ADC.
description		Read-only	Display the type of interface, the speeds at which this interface can operate, and, if applicable, the type of SFP,.
flags		Read-only	Flags for this interface. Used for communicating the device states.
actualmtu		Read-only	MTU for this interface (the largest frame that can transit this interface).
vlan		Read-only	Native VLAN for this interface.
mac		Read-only	MAC address for this interface.
uptime		Read-only	Duration for which the interface has been UP (Example: 3 hours 1 minute 1 second). This value is reset when the interface state changes to DOWN..
downtime		Read-only	Duration for which the interface has been DOWN. This value is reset when the interface state changes to UP.(Example: 3 hours 1 minute 1 second).
actualringsize		Read-only	Actual receive ringsize of the interface. This will be same as configured receive ringsize when ringtype is Fixed whereas it denotes the current number of receive buffers allocated when ringtype is Elastic.
reqmedia		Read-only	Requested media setting for this interface. Possible values = AUTO, UTP, FIBER
reqspeed		Read-only	Requested speed setting for this interface. Possible values = AUTO, 10, 100, 1000, 10000, 25000, 40000, 50000, 100000
reqduplex		Read-only	Requested duplex setting for this interface. Possible values = AUTO, HALF, FULL
reqflowcontrol		Read-only	Requested flow control setting for this interface. Possible values = OFF, RX, TX, RXTX, ON
actmedia		Read-only	Actual media setting for this interface. Possible values = AUTO, UTP, FIBER
actspeed		Read-only	Actual speed setting for this interface. Possible values = AUTO, 10, 100, 1000, 10000, 25000, 40000, 50000, 100000
actduplex		Read-only	Actual duplex setting for this interface. Possible values = AUTO, HALF, FULL
actflowctl		Read-only	Actual flow control setting for this interface. Possible values = OFF, RX, TX, RXTX, ON
mode		Read-only	Interface Link Aggregation mode (Auto/Manual) setting. Possible values = MANUAL, AUTO
state		Read-only	Link state of the interface (UP/DOWN). Default value: ENABLED Possible values = ENABLED, DISABLED
autonegresult		Read-only	Actual auto-negotiation setting for this interface.
tagged		Read-only	VLAN tags setting on this channel.
taggedany		Read-only	Interface setting to accept/drop all tagged packets.
taggedautolearn		Read-only	Dynamic VLAN membership autolearning enabled or disabled on this interface.
hangdetect		Read-only	Hang detection enabled or disabled for this interface.
hangreset		Read-only	Hang reset enabled or disabled for this interface.
linkstate		Read-only	The current state of the link associated with the interface. For logical interfaces (LA), the state of the link is dependent on the state of the slave interfaces. For the link to be UP at least one of the slave interfaces needs to be UP.
intfstate		Read-only	Current state of the specified interface. The interface state set to UP only if the link state is UP and administrative state is ENABLED.
rxpackets		Read-only	Number of packets received by an interface since the Citrix ADC was started or the interface statistics were cleared.
rxbytes		Read-only	Number of bytes received by an interface since the Citrix ADC was started or the interface statistics were cleared.
rxerrors		Read-only	Number of inbound packets dropped by the hardware on a specified interface since the Citrix ADC was started or the interface statistics were cleared. Packets can be dropped because of CRC, length (undersize or oversize), or alignment errors.
rxdrops		Read-only	Number of inbound packets dropped by the specified interface. Commonly dropped packets are multicast frames, spanning tree BPDUs, packets destined to a MAC not owned by the Citrix ADC when L2 mode is disabled, or packets tagged for a VLAN that is not bound to the interface. In most healthy networks, this statistic increments at a steady rate regardless of traffic load. A sharp spike in dropped packets generally indicates an issue with connected L2 switches, such as a forwarding database overflow resulting in packets being broadcast on all ports.
txpackets		Read-only	Number of packets transmitted by an interface since the Citrix ADC was started or the interface statistics were cleared.
txbytes		Read-only	Number of bytes transmitted by an interface since the Citrix ADC was started or the interface statistics were cleared.
txerrors		Read-only	Number of outbound packets dropped by the hardware on a specified interface since the Citrix ADC was started or the interface statistics were cleared. Packets can be dropped because of length (undersize or oversize) errors or a lack of resources. This statistic is available only for (1) Loop back interface (LO) of all platforms. (2) All data ports on the Citrix ADC 12000 platform. (3) Management ports on the Citrix ADC MPX 15000 and 17000 platforms. .
txdrops		Read-only	Number of packets dropped in transmission by the specified interface for one of the following reasons. (1) VLAN mismatch. (2) Oversized packets. (3) Interface congestion. (4) Loopback packets sent on non loop back interface. .
indisc		Read-only	Number of error-free inbound packets discarded by the specified interface because of a lack of resources (for example, insufficient receive buffers).
outdisc		Read-only	Number of error-free outbound packets discarded by the specified interface because of a lack of resources. This statistic is not available on (1) 10G ports of Citrix ADC MPX 12500/12500/15500-10G platforms. (2) 10G data ports on Citrix ADC MPX 17500/19500/21500 platforms. .
fctls		Read-only	Number of times flow control is performed on the specified interface because of received pause frames.
hangs		Read-only	Number of times the specified interface detected hangs in the transmit and receive paths since the Citrix ADC was started or the interface statistics were cleared.
stsstalls		Read-only	Number of times the status updates for a specified interface were stalled since the Citrix ADC was started or the interface statistics were cleared. A status stall is detected when the status of the interface is not updated by the NIC hardware within 0.8 seconds of the last update.
txstalls		Read-only	Number of times the interface stalled, when transmitting packets, since the Citrix ADC was started or the interface statistics were cleared. Transmit (Tx) stalls are detected when a packet posted for transmission is not transmitted in 4 seconds.
rxstalls		Read-only	Number of times the interface stalled, when receiving packets, since the Citrix ADC was started or the interface statistics were cleared. Receive (Rx) stalls are detected when the following conditions are met (1)The link is up for more than 10 minutes. (2)Packets are transmitted, but no packets are received for 16 seconds. .
bdgmacmoved		Read-only	Number of MAC moves between ports. A high rate of MAC moves typically indicates a bridge loop between two interfaces.
bdgmuted		Read-only	Number of times the specified interface stopped transmitting and receiving packets because of MAC moves between ports.
vmac		Read-only	Virtual MAC of this interface.
vmac6		Read-only	Virtual MAC for IPv6 of this interface.
reqthroughput		Read-only	Minimum required throughput for an interface. Failover is triggered if the operating throughput of a Link Aggregation (LA) channel for which HAMON is ON falls below this value. The possible values are 1000Mbps for 1G interfaces. 10000Mbps for 10G interfaces. 160000Mbps for Link Aggregation channels. Minimum value = 0 Maximum value = 160000
actthroughput		Read-only	Actual throughput for the interface.
backplane		Read-only	The cluster backplane status of the interface. If the status is enabled, the interface is part of the cluster backplane. By default, the backplane status is disabled. Possible values = ENABLED, DISABLED
ifnum	<String[]>	Read-only	Contains the LA Master, if the interface is part of LA channel.
cleartime		Read-only	Time since the interface stats are cleared last time.
slavestate		Read-only	State of the member interfaces.
slavemedia		Read-only	Media type of the member interfaces.
slavespeed		Read-only	Speed of the member interfaces.
slaveduplex		Read-only	Duplex of the member interfaces.
slaveflowctl		Read-only	Flowcontrol of the member interfaces.
slavetime		Read-only	UP time of the member interfaces.
intftype		Read-only	Interface Type, this field will have the interface type either it is virtual, physical or loopback. . Possible values = BROADCOM 5700/5701, TIGON1/TIGON2, INTEL 82546, INTEL 8255X(PRO), Link Aggregate, Loopback, Intel 82541/47, Broadcom 5704, Chelsio 1G, Intel 8247X, Intel 82576 VF, Xen Virtual, Intel 10G, Intel 82599 VF, Mellanox 100G, Mellanox 50G, Mellanox 25G, Intel FVL 40G, Intel FVL 25G, Intel FVL 10G, Intel FVL 40G VF, Mellanox VF, Hyper v, Cluster LAG, Intel 8247X SFP, XEN Interface, Chelsio 10G, KVM Virtio, VMXNET3
svmcmd		Read-only	New attribute added to identify the source of cmd, when SVM fires the nitro cmd, it will set the value of SVMCMD to be 1. . Default value: 0
lacpactormode		Read-only	* Active - The LA channel port of the Citrix ADC generates LACPDU messages on a regular basis, regardless of any need expressed by its peer device to receive them. * Passive - The LA channel port of the Citrix ADC does not transmit LACPDU messages unless the peer device port is in the active mode. That is, the port does not speak unless spoken to. * Disabled - Unbinds the interface from the LA channel. If this is the only interface in the LA channel, the LA channel is removed. Possible values = DISABLED, ACTIVE, PASSIVE
lacpactortimeout		Read-only	Interval at which the Citrix ADC sends LACPDU messages to the peer device on the LA channel. Available settings function as follows LONG - 30 seconds. SHORT - 1 second. Possible values = LONG, SHORT
lacpactorpriority		Read-only	LACP Actor Priority. A LACP port priority is configured on each port using LACP. LACP uses the port priority with the port number to form the port identifier. The port priority determines which ports should be put in standby mode when there is a hardware limitation that prevents all compatible ports from aggregating.
lacpactorportno		Read-only	LACP Actor port number. LACP uses the port priority with the port number to form the port identifier.
lacppartnerstate		Read-only	LACP Partner State. Whether the port is in Active or Passive negotiating state. Possible values = MANUAL, AUTO
lacppartnertimeout		Read-only	The timeout value for the information revieved in LACPDUs. It can have values as SHORT or LONG. The SHORT timeout is 3s and the LONG timeout is 90s. Possible values = LONG, SHORT
lacppartneraggregation		Read-only	The Aggregation flag indicates that the participant will allow the link to be used as part of an aggregate. Otherwise the link is to be used as an individual link, i.e. not aggregated with any other. Possible values = NS_EMPTY_STR, AGG
lacppartnerinsync		Read-only	The Synchronization flag indicates that the transmitting participant.s mux component is in sync with the system id and key information transmitted. Possible values = NS_EMPTY_STR, SYNC
lacppartnercollecting		Read-only	The Collecting flag indicates that the participant.s collector, i.e. the reception component of the mux, is definitely on. If set the flag communicates collecting. Possible values = NS_EMPTY_STR, COLLECTING
lacppartnerdistributing		Read-only	The Distributing flag indicates that the participant.s distributor is not definitely off. If reset the flag indicates not distributing. Possible values = NS_EMPTY_STR, DISTRIBUTING
lacppartnerdefaulted		Read-only	If the timer expires in the Expired state, the Receive Machine enters the Defaulted state. Possible values = NS_EMPTY_STR, DEFAULTED
lacppartnerexpired		Read-only	If the LACPDUs are received for timeout period, the Receive Machine enters the Expired state and the timer is restarted with the timeout value of SHORT timeout. Possible values = NS_EMPTY_STR, EXPIRED
lacppartnerpriority		Read-only	LACP Partner Priority. A LACP port priority is configured on each port using LACP. LACP uses the port priority with the port number to form the port identifier. The port priority determines which ports should be put in standby mode when there is a hardware limitation that prevents all compatible ports from aggregating.
lacppartnersystemmac		Read-only	LACP Partner System MAC.
lacppartnersystempriority		Read-only	LACP Partner System Priority. The LACP partner’s system priority. The values for the priority range from 0 to 65535. The lower the value, the higher the system priority. The switch with the lower system priority value determines which links between LACP partner are active and which are in the standby for each LACP Channel.
lacppartnerportno		Read-only	LACP Partner Port number. LACP uses the port priority with the port number to form the port identifier.
lacppartnerkey		Read-only	LACP Partner Key. The LACP key used by the partner port.
lacpactoraggregation		Read-only	The Aggregation flag indicates that the participant will allow the link to be used as part of an aggregate. Otherwise the link is to be used as an individual link, i.e. not aggregated with any other. Possible values = NS_EMPTY_STR, AGG
lacpactorinsync		Read-only	The Synchronization flag indicates that the transmitting participant.s mux component is in sync with the system id and key information transmitted. Possible values = NS_EMPTY_STR, SYNC
lacpactorcollecting		Read-only	The Collecting flag indicates that the participant.s collector, i.e. the reception component of the mux, is definitely on. If set the flag communicates collecting. Possible values = NS_EMPTY_STR, COLLECTING
lacpactordistributing		Read-only	The Distributing flag indicates that the participant.s distributor is not definitely off. If reset the flag indicates not distributing. Possible values = NS_EMPTY_STR, DISTRIBUTING
lacpportmuxstate		Read-only	LACP Port MUX state. The state of the MUX control machine. The Mux Control Machine attaches the physical port to an aggregate port, using the Selection Logic to choose an appropriate port, and turns the distributor and collector for the physical port on or off as required by protocol information. Possible values = DETACHED, WAITING, ATTACHED, COLLECTING, DISTRIBUTING
lacpportrxstat		Read-only	LACP Port RX state. The state of the Receive machine. The Receive Machine maintains partner information, recording protocol information from LACPDUs sent by remote partner(s). Received information is subject to a timeout, and if sufficient time elapses the receive machine will revert to using default partner information. Possible values = INIT, PORT_DISABLED, LACP_DISABLED, EXPIRED, DEFAULTED, CURRENT
lacpportselectstate		Read-only	LACP Port SELECT state. The state of the SELECT state machine, It could be SELECTED or UNSELECTED. Possible values = UNSELECTED, SELECTED, STANDBY
lractiveintf		Read-only	LR set member interface state(active/inactive).
__count		Read-only	count parameter

Operations

(click to see Properties )

CLEAR
UPDATE
UNSET
ENABLE
DISABLE
RESET
GET (ALL)
GET
COUNT

Some options that you can use for each operations:

Getting warnings in response: NITRO allows you to get warnings in an operation by specifying the 'warning' query parameter as 'yes'. For example, to get warnings while connecting to the NetScaler appliance, the URL is as follows:

http:// <netscaler-ip-address> /nitro/v1/config/login?warning=yes

If any, the warnings are displayed in the response payload with the HTTP code '209 X-NITRO-WARNING'.
Authenticated access for individual NITRO operations: NITRO allows you to logon to the NetScaler appliance to perform individual operations. You can use this option instead of creating a NITRO session (using the login object) and then using that session to perform all operations,

To do this, you must specify the username and password in the request header of the NITRO request as follows:

X-NITRO-USER: <username>

X-NITRO-PASS: <password>

Note: In such cases, make sure that the request header DOES not include the following:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

*Note:*

Mandatory parameters are marked in red and placeholder content is marked in green

clear

URL: http:// <netscaler-ip-address> /nitro/v1/config/Interface? action=clear

HTTP Method: POST

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Content-Type:application/json

Request Payload:

{"Interface":{
<b>      "id":<String_value>
</b>}}

<!--NeedCopy-->

Response:

HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

update

URL: http:// <netscaler-ip-address> /nitro/v1/config/Interface

HTTP Method: PUT

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Content-Type:application/json

Request Payload:

{"Interface":{
<b>      "id":<String_value>,
</b>      "speed":<String_value>,
      "duplex":<String_value>,
      "flowctl":<String_value>,
      "autoneg":<String_value>,
      "hamonitor":<String_value>,
      "haheartbeat":<String_value>,
      "mtu":<Double_value>,
      "ringsize":<Double_value>,
      "ringtype":<String_value>,
      "tagall":<String_value>,
      "trunk":<String_value>,
      "trunkmode":<String_value>,
      "trunkallowedvlan":<String[]_value>,
      "lacpmode":<String_value>,
      "lacpkey":<Double_value>,
      "lagtype":<String_value>,
      "lacppriority":<Double_value>,
      "lacptimeout":<String_value>,
      "ifalias":<String_value>,
      "throughput":<Double_value>,
      "linkredundancy":<String_value>,
      "bandwidthhigh":<Double_value>,
      "bandwidthnormal":<Double_value>,
      "lldpmode":<String_value>,
      "lrsetpriority":<Double_value>
}}

<!--NeedCopy-->

Response:

HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

unset

URL: http:// <netscaler-ip-address> /nitro/v1/config/Interface? action=unset

HTTP Method: POST

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Content-Type:application/json

Request Payload:

{"Interface":{
<b>      "id":<String_value>,
</b>      "speed":true,
      "duplex":true,
      "flowctl":true,
      "autoneg":true,
      "hamonitor":true,
      "haheartbeat":true,
      "mtu":true,
      "ringsize":true,
      "ringtype":true,
      "tagall":true,
      "trunk":true,
      "trunkmode":true,
      "trunkallowedvlan":true,
      "lacpmode":true,
      "lacppriority":true,
      "lacptimeout":true,
      "ifalias":true,
      "throughput":true,
      "linkredundancy":true,
      "bandwidthhigh":true,
      "bandwidthnormal":true,
      "lldpmode":true,
      "lrsetpriority":true
}}

<!--NeedCopy-->

Response:

HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

enable

URL: http:// <netscaler-ip-address> /nitro/v1/config/Interface? action=enable

HTTP Method: POST

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Content-Type:application/json

Request Payload:

{"Interface":{
<b>      "id":<String_value>
</b>}}

<!--NeedCopy-->

Response:

HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

disable

URL: http:// <netscaler-ip-address> /nitro/v1/config/Interface? action=disable

HTTP Method: POST

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Content-Type:application/json

Request Payload:

{"Interface":{
<b>      "id":<String_value>
</b>}}

<!--NeedCopy-->

Response:

HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

reset

URL: http:// <netscaler-ip-address> /nitro/v1/config/Interface? action=reset

HTTP Method: POST

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Content-Type:application/json

Request Payload:

{"Interface":{
<b>      "id":<String_value>
</b>}}

<!--NeedCopy-->

Response:

HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

get (all)

URL: http:// <netscaler-ip-address> /nitro/v1/config/Interface

Query-parameters:

attrs

http:// <netscaler-ip-address> /nitro/v1/config/Interface? attrs=property-name1,property-name2

Use this query parameter to specify the resource details that you want to retrieve.

filter

http:// <netscaler-ip-address> /nitro/v1/config/Interface? filter=property-name1:property-val1,property-name2:property-val2

Use this query-parameter to get the filtered set of Interface resources configured on NetScaler.Filtering can be done on any of the properties of the resource.

view

http:// <netscaler-ip-address> /nitro/v1/config/Interface? view=summary

Use this query-parameter to get the summary output of Interface resources configured on NetScaler.

Note: By default, the retrieved results are displayed in detail view (?view=detail).

pagination

http:// <netscaler-ip-address> /nitro/v1/config/Interface? pagesize=#no;pageno=#no

Use this query-parameter to get the Interface resources in chunks.

HTTP Method: GET

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Accept:application/json

Response:

HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

Response Header:

Content-Type:application/json

Response Payload:

{ "Interface": [ {
      "id":<String_value>,
      "devicename":<String_value>,
      "unit":<Double_value>,
      "description":<String_value>,
      "flags":<Double_value>,
      "mtu":<Double_value>,
      "actualmtu":<Double_value>,
      "vlan":<Double_value>,
      "mac":<String_value>,
      "uptime":<Double_value>,
      "downtime":<Double_value>,
      "ringsize":<Double_value>,
      "ringtype":<String_value>,
      "actualringsize":<Double_value>,
      "reqmedia":<String_value>,
      "reqspeed":<String_value>,
      "reqduplex":<String_value>,
      "reqflowcontrol":<String_value>,
      "actmedia":<String_value>,
      "actspeed":<String_value>,
      "actduplex":<String_value>,
      "actflowctl":<String_value>,
      "mode":<String_value>,
      "hamonitor":<String_value>,
      "haheartbeat":<String_value>,
      "state":<String_value>,
      "autoneg":<String_value>,
      "autonegresult":<Double_value>,
      "tagged":<Double_value>,
      "tagall":<String_value>,
      "trunk":<String_value>,
      "trunkmode":<String_value>,
      "trunkallowedvlan":<String[]_value>,
      "taggedany":<Double_value>,
      "taggedautolearn":<Double_value>,
      "hangdetect":<Double_value>,
      "hangreset":<Double_value>,
      "linkstate":<Double_value>,
      "intfstate":<Double_value>,
      "rxpackets":<Double_value>,
      "rxbytes":<Double_value>,
      "rxerrors":<Double_value>,
      "rxdrops":<Double_value>,
      "txpackets":<Double_value>,
      "txbytes":<Double_value>,
      "txerrors":<Double_value>,
      "txdrops":<Double_value>,
      "indisc":<Double_value>,
      "outdisc":<Double_value>,
      "fctls":<Double_value>,
      "hangs":<Double_value>,
      "stsstalls":<Double_value>,
      "txstalls":<Double_value>,
      "rxstalls":<Double_value>,
      "bdgmacmoved":<Double_value>,
      "bdgmuted":<Double_value>,
      "vmac":<String_value>,
      "vmac6":<String_value>,
      "lacpmode":<String_value>,
      "lacpkey":<Double_value>,
      "lacppriority":<Double_value>,
      "lacptimeout":<String_value>,
      "lagtype":<String_value>,
      "ifalias":<String_value>,
      "reqthroughput":<Double_value>,
      "linkredundancy":<String_value>,
      "actthroughput":<Double_value>,
      "bandwidthhigh":<Double_value>,
      "bandwidthnormal":<Double_value>,
      "backplane":<String_value>,
      "ifnum":<String[]_value>,
      "cleartime":<Double_value>,
      "slavestate":<Double_value>,
      "slavemedia":<Double_value>,
      "slavespeed":<Double_value>,
      "slaveduplex":<Double_value>,
      "slaveflowctl":<Double_value>,
      "slavetime":<Double_value>,
      "intftype":<String_value>,
      "svmcmd":<Double_value>,
      "lacpactormode":<String_value>,
      "lacpactortimeout":<String_value>,
      "lacpactorpriority":<Double_value>,
      "lacpactorportno":<Double_value>,
      "lacppartnerstate":<String_value>,
      "lacppartnertimeout":<String_value>,
      "lacppartneraggregation":<String_value>,
      "lacppartnerinsync":<String_value>,
      "lacppartnercollecting":<String_value>,
      "lacppartnerdistributing":<String_value>,
      "lacppartnerdefaulted":<String_value>,
      "lacppartnerexpired":<String_value>,
      "lacppartnerpriority":<Double_value>,
      "lacppartnersystemmac":<String_value>,
      "lacppartnersystempriority":<Double_value>,
      "lacppartnerportno":<Double_value>,
      "lacppartnerkey":<Double_value>,
      "lacpactoraggregation":<String_value>,
      "lacpactorinsync":<String_value>,
      "lacpactorcollecting":<String_value>,
      "lacpactordistributing":<String_value>,
      "lacpportmuxstate":<String_value>,
      "lacpportrxstat":<String_value>,
      "lacpportselectstate":<String_value>,
      "lldpmode":<String_value>,
      "lrsetpriority":<Double_value>,
      "lractiveintf":<Boolean_value>
}]}

<!--NeedCopy-->

get

URL: http:// <netscaler-ip-address> /nitro/v1/config/Interface/ id_value<String>

Query-parameters:

attrs

http:// <netscaler-ip-address> /nitro/v1/config/Interface/ id_value<String> ? attrs=property-name1,property-name2

Use this query parameter to specify the resource details that you want to retrieve.

view

http:// <netscaler-ip-address> /nitro/v1/config/Interface/ id_value<String> ? view=summary

Use this query-parameter to get the summary output of Interface resources configured on NetScaler.

Note: By default, the retrieved results are displayed in detail view (?view=detail).

HTTP Method: GET

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Accept:application/json

Response:

HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

Response Header:

Content-Type:application/json

Response Payload:

{  "Interface": [ {
      "id":<String_value>,
      "devicename":<String_value>,
      "unit":<Double_value>,
      "description":<String_value>,
      "flags":<Double_value>,
      "mtu":<Double_value>,
      "actualmtu":<Double_value>,
      "vlan":<Double_value>,
      "mac":<String_value>,
      "uptime":<Double_value>,
      "downtime":<Double_value>,
      "ringsize":<Double_value>,
      "ringtype":<String_value>,
      "actualringsize":<Double_value>,
      "reqmedia":<String_value>,
      "reqspeed":<String_value>,
      "reqduplex":<String_value>,
      "reqflowcontrol":<String_value>,
      "actmedia":<String_value>,
      "actspeed":<String_value>,
      "actduplex":<String_value>,
      "actflowctl":<String_value>,
      "mode":<String_value>,
      "hamonitor":<String_value>,
      "haheartbeat":<String_value>,
      "state":<String_value>,
      "autoneg":<String_value>,
      "autonegresult":<Double_value>,
      "tagged":<Double_value>,
      "tagall":<String_value>,
      "trunk":<String_value>,
      "trunkmode":<String_value>,
      "trunkallowedvlan":<String[]_value>,
      "taggedany":<Double_value>,
      "taggedautolearn":<Double_value>,
      "hangdetect":<Double_value>,
      "hangreset":<Double_value>,
      "linkstate":<Double_value>,
      "intfstate":<Double_value>,
      "rxpackets":<Double_value>,
      "rxbytes":<Double_value>,
      "rxerrors":<Double_value>,
      "rxdrops":<Double_value>,
      "txpackets":<Double_value>,
      "txbytes":<Double_value>,
      "txerrors":<Double_value>,
      "txdrops":<Double_value>,
      "indisc":<Double_value>,
      "outdisc":<Double_value>,
      "fctls":<Double_value>,
      "hangs":<Double_value>,
      "stsstalls":<Double_value>,
      "txstalls":<Double_value>,
      "rxstalls":<Double_value>,
      "bdgmacmoved":<Double_value>,
      "bdgmuted":<Double_value>,
      "vmac":<String_value>,
      "vmac6":<String_value>,
      "lacpmode":<String_value>,
      "lacpkey":<Double_value>,
      "lacppriority":<Double_value>,
      "lacptimeout":<String_value>,
      "lagtype":<String_value>,
      "ifalias":<String_value>,
      "reqthroughput":<Double_value>,
      "linkredundancy":<String_value>,
      "actthroughput":<Double_value>,
      "bandwidthhigh":<Double_value>,
      "bandwidthnormal":<Double_value>,
      "backplane":<String_value>,
      "ifnum":<String[]_value>,
      "cleartime":<Double_value>,
      "slavestate":<Double_value>,
      "slavemedia":<Double_value>,
      "slavespeed":<Double_value>,
      "slaveduplex":<Double_value>,
      "slaveflowctl":<Double_value>,
      "slavetime":<Double_value>,
      "intftype":<String_value>,
      "svmcmd":<Double_value>,
      "lacpactormode":<String_value>,
      "lacpactortimeout":<String_value>,
      "lacpactorpriority":<Double_value>,
      "lacpactorportno":<Double_value>,
      "lacppartnerstate":<String_value>,
      "lacppartnertimeout":<String_value>,
      "lacppartneraggregation":<String_value>,
      "lacppartnerinsync":<String_value>,
      "lacppartnercollecting":<String_value>,
      "lacppartnerdistributing":<String_value>,
      "lacppartnerdefaulted":<String_value>,
      "lacppartnerexpired":<String_value>,
      "lacppartnerpriority":<Double_value>,
      "lacppartnersystemmac":<String_value>,
      "lacppartnersystempriority":<Double_value>,
      "lacppartnerportno":<Double_value>,
      "lacppartnerkey":<Double_value>,
      "lacpactoraggregation":<String_value>,
      "lacpactorinsync":<String_value>,
      "lacpactorcollecting":<String_value>,
      "lacpactordistributing":<String_value>,
      "lacpportmuxstate":<String_value>,
      "lacpportrxstat":<String_value>,
      "lacpportselectstate":<String_value>,
      "lldpmode":<String_value>,
      "lrsetpriority":<Double_value>,
      "lractiveintf":<Boolean_value>
}]}

<!--NeedCopy-->

count

URL: http:// <netscaler-ip-address> /nitro/v1/config/Interface? count=yes

HTTP Method: GET

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Accept:application/json

Response:

HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

Response Header:

Content-Type:application/json

Response Payload:

{ "Interface": [ { "__count": "#no"} ] }

<!--NeedCopy-->

The official version of this content is in English. Some of the Cloud Software Group documentation content is machine translated for your convenience only. Cloud Software Group has no control over machine-translated content, which may contain errors, inaccuracies or unsuitable language. No warranty of any kind, either expressed or implied, is made as to the accuracy, reliability, suitability, or correctness of any translations made from the English original into any other language, or that your Cloud Software Group product or service conforms to any machine translated content, and any warranty provided under the applicable end user license agreement or terms of service, or any other agreement with Cloud Software Group, that the product or service conforms with any documentation shall not apply to the extent that such documentation has been machine translated. Cloud Software Group will not be held responsible for any damage or issues that may arise from using machine-translated content.

Was this helpful

Interface

August 17, 2023

Contributed by:

August 17, 2023

Contributed by:

Interface

Properties

Operations

clear

update

unset

enable

disable

reset

get (all)

get

count

In this article