Developer Documentation

ADC CLI Commands

lldp-neighbors

May 28, 2024

Contributed by:

The following operations can be performed on “lldp-neighbors”:

show

clear

show lldp neighbors

Display Neighbor information per interface

Synopsis

show lldp neighbors []

Arguments

ifnum Interface Name

Output

chassisIdSubtype Chassis id sub type

chassisId Chassis Id

portIdSubtype Port id subtype

portId Port Id

TTL Time to Live

portDescription Port Description

sys System Name

sysDesc System Description

mgmtAddressSubtype Management Address Type

mgmtAddress Management Address

iftype Interface subtype

ifNumber Interface Number

vlan vlan name

vlanId Vlan Id

portProtoSupported Flag to show Port Protocol Support

portProtoEnabled Flag to show Port Protocol support enabled

portProtoId Port Protocol ID

portVlanId Port Vlan Id

protocolId port vlan id name

linkAggrCapable Is neighbor Link Aggregation Capable

LinkAggrEnabled Is link aggregation Enabled

linkAggrId Link Aggregation Id

flag sysCapabilities Temp System Capabilities

sysCapabilities Acronyms for remote system capabilities: OT : Other. RE : Repeater(IETF RFC 2108). BR : MAC Bridge(IEEE Std 802.1D). WL : WLAN Access Point(IEEE Std 802.11 MIB). RO : ROuter(IETF RFC 1812). TE : Telephone(IETF RFC 4293). DO : DOCSIS cable device(IETF RFC 4639 and IETF RFC 4546). ST : STation only(IETF RFC 4293). CV : C-VLAN component of a VLAN Bridge(IEEE Std 802.1Q). SV : S-VLAN component of a VLAN Bridge(IEEE Std 802.1Q). MR : Two port MAC Relay(IEEE Std 802.1Q).

sysCapEnabled Temp system enabled capabilities

sysCapEnabled Acronyms for remote system enabled capabilities: OT : Other. RE : Repeater(IETF RFC 2108). BR : MAC Bridge(IEEE Std 802.1D). WL : WLAN Access Point(IEEE Std 802.11 MIB). RO : ROuter(IETF RFC 1812). TE : Telephone(IETF RFC 4293). DO : DOCSIS cable device(IETF RFC 4639 and IETF RFC 4546). ST : STation only(IETF RFC 4293). CV : C-VLAN component of a VLAN Bridge(IEEE Std 802.1Q). SV : S-VLAN component of a VLAN Bridge(IEEE Std 802.1Q). MR : Two port MAC Relay(IEEE Std 802.1Q).

autonegSupport MAC/PHY autonegotiation support

autonegEnabled MAC/PHY autonegotiation enabled

autonegAdvertised MAC/PHY autonegotiation advetised

autonegMAUType MAC/PHY Medium Attachment Unit (MAU) type of the port. Description listed below: AUI - no internal MAU, view from AUI 10Base5 - thick coax MAU Foirl - FOIRL MAU 10Base2 - thin coax MAU 10BaseT - UTP MAU 10BaseFP - passive fiber MAU 10BaseFB - sync fiber MAU 10BaseFL - async fiber MAU 10Broad36 - broadband DTE MAU 10BaseTHD - UTP MAU, half duplex mode 10BaseTFD - UTP MAU, full duplex mode 10BaseFLHD - async fiber MAU, half duplex mode 10BaseFLDF - async fiber MAU, full duplex mode 10BaseT4 - 4 pair category 3 UTP 100BaseTXHD - 2 pair category 5 UTP, half duplex mode 100BaseTXFD - 2 pair category 5 UTP, full duplex mode 100BaseFXHD - X fiber over PMT, half duplex mode 100BaseFXFD - X fiber over PMT, full duplex mode 100BaseT2HD - 2 pair category 3 UTP, half duplex mode 100BaseT2DF - 2 pair category 3 UTP, full duplex mode 1000BaseXHD - PCS/PMA, unknown PMD, half duplex mode 1000BaseXFD - PCS/PMA, unknown PMD, full duplex mode 1000BaseLXHD - Fiber over long-wavelength laser, half duplex mode 1000BaseLXFD - Fiber over long-wavelength laser, full duplex mode 1000BaseSXHD - Fiber over short-wavelength laser, half duplex mode 1000BaseSXFD - Fiber over short-wavelength laser, full duplex mode 1000BaseCXHD - Copper over 150-Ohm balanced cable, half duplex mode 1000BaseCXFD - Copper over 150-Ohm balanced cable, full duplex mode 1000BaseTHD - Four-pair Category 5 UTP, half duplex mode 1000BaseTFD - Four-pair Category 5 UTP, full duplex mode 10GigBaseX - X PCS/PMA, unknown PMD 10GigBaseLX4 - X fiber over WWDM optics 10GigBaseR - R PCS/PMA, unknown PMD 10GigBaseER - R fiber over 1550 nm optics 10GigBaseLR - R fiber over 1310 nm optics 10GigBaseSR - R fiber over 850 nm optics 10GigBaseW - W PCS/PMA, unknown PMD 10GigBaseEW - W fiber over 1550 nm optics 10GigBaseLW - W fiber over 1310 nm optics 10GigBaseSW - W fiber over 850 nm optics

mtu MTU of Remote Device

devno count stateflag

clear lldp neighbors

Removes LLDP neighbor info of interfaces

Synopsis

clear lldp neighbors

The official version of this content is in English. Some of the Cloud Software Group documentation content is machine translated for your convenience only. Cloud Software Group has no control over machine-translated content, which may contain errors, inaccuracies or unsuitable language. No warranty of any kind, either expressed or implied, is made as to the accuracy, reliability, suitability, or correctness of any translations made from the English original into any other language, or that your Cloud Software Group product or service conforms to any machine translated content, and any warranty provided under the applicable end user license agreement or terms of service, or any other agreement with Cloud Software Group, that the product or service conforms with any documentation shall not apply to the extent that such documentation has been machine translated. Cloud Software Group will not be held responsible for any damage or issues that may arise from using machine-translated content.

Was this helpful

lldp-neighbors

May 28, 2024

Contributed by:

May 28, 2024

Contributed by:

lldp-neighbors

show lldp neighbors

Synopsis

Arguments

Output

clear lldp neighbors

Synopsis

In this article