-
-
-
-
-
-
L3Param
-
-
-
-
-
This content has been machine translated dynamically.
Dieser Inhalt ist eine maschinelle Übersetzung, die dynamisch erstellt wurde. (Haftungsausschluss)
Cet article a été traduit automatiquement de manière dynamique. (Clause de non responsabilité)
Este artículo lo ha traducido una máquina de forma dinámica. (Aviso legal)
此内容已经过机器动态翻译。 放弃
このコンテンツは動的に機械翻訳されています。免責事項
이 콘텐츠는 동적으로 기계 번역되었습니다. 책임 부인
Este texto foi traduzido automaticamente. (Aviso legal)
Questo contenuto è stato tradotto dinamicamente con traduzione automatica.(Esclusione di responsabilità))
This article has been machine translated.
Dieser Artikel wurde maschinell übersetzt. (Haftungsausschluss)
Ce article a été traduit automatiquement. (Clause de non responsabilité)
Este artículo ha sido traducido automáticamente. (Aviso legal)
この記事は機械翻訳されています.免責事項
이 기사는 기계 번역되었습니다.책임 부인
Este artigo foi traduzido automaticamente.(Aviso legal)
这篇文章已经过机器翻译.放弃
Questo articolo è stato tradotto automaticamente.(Esclusione di responsabilità))
Translation failed!
L3Param
The following operations can be performed on “L3Param”:
show | set | unset |
show L3Param
Displays the settings of global Layer 3 parameters.
Synopsis
show L3Param
Arguments
Output
srcnat Perform NAT if only the source is in the private network
icmpGenRateThreshold NS generated ICMP pkts per 10ms rate threshold
overrideRnat USNIP/USIP settings override RNAT settings for configured service/virtual server traffic..
dropDFFlag Enable dropping the IP DF flag.
mipRoundRobin Enable round robin usage of mapped IPs.
externalLoopBack Enable external loopback.
tnlPmtuWoConn Enable/Disable learning PMTU of IP tunnel when ICMP error does not contain connection information.
usipServerStrayPkt Enable detection of stray server side pkts in USIP mode.
forwardICMPFragments Enable forwarding of ICMP fragments.
dropIPFragments Enable dropping of IP fragments.
AclLogTime Parameter to tune acl logging time
implicitACLAllow Do not apply ACLs for internal ports
dynamicRouting Enable/Disable Dynamic routing on partition. This configuration is not applicable to default partition
ipv6DynamicRouting Enable/Disable IPv6 Dynamic routing
allowClassEIPv4 Enable/Disable IPv4 Class E address clients
implicitPBR Enable/Disable Policy Based Routing for control packets
Related Commands
set L3Param
Set Layer 3 related global settings on the Citrix ADC
Synopsis
set L3Param [-srcnat ( ENABLED | DISABLED )] [-icmpGenRateThreshold |
DISABLED )] [-dropDFFlag ( ENABLED | DISABLED )] [-mipRoundRobin ( ENABLED | DISABLED )] [-externalLoopBack ( ENABLED | DISABLED )] [-tnlPmtuWoConn ( ENABLED | DISABLED )] [-usipServerStrayPkt ( ENABLED | DISABLED )] [-forwardICMPFragments ( ENABLED | DISABLED )] [-dropIPFragments ( ENABLED | DISABLED )] [-AclLogTime |
DISABLED )] [-dynamicRouting ( ENABLED | DISABLED )] [-ipv6DynamicRouting ( ENABLED | DISABLED )] [-allowClassEIPv4 ( ENABLED | DISABLED )] [-implicitPBR ( ENABLED | DISABLED )] |
Arguments
srcnat Perform NAT if only the source is in the private network
Possible values: ENABLED, DISABLED Default value: ENABLED
icmpGenRateThreshold NS generated ICMP pkts per 10ms rate threshold Default value: 100 Minimum value: 0
overrideRnat USNIP/USIP settings override RNAT settings for configured service/virtual server traffic..
Possible values: ENABLED, DISABLED Default value: DISABLED
dropDFFlag Enable dropping the IP DF flag.
Possible values: ENABLED, DISABLED Default value: DISABLED
mipRoundRobin Enable round robin usage of mapped IPs.
Possible values: ENABLED, DISABLED Default value: ENABLED
externalLoopBack Enable external loopback.
Possible values: ENABLED, DISABLED Default value: DISABLED
tnlPmtuWoConn Enable/Disable learning PMTU of IP tunnel when ICMP error does not contain connection information.
Possible values: ENABLED, DISABLED Default value: ENABLED
usipServerStrayPkt Enable detection of stray server side pkts in USIP mode.
Possible values: ENABLED, DISABLED Default value: DISABLED
forwardICMPFragments Enable forwarding of ICMP fragments.
Possible values: ENABLED, DISABLED Default value: DISABLED
dropIPFragments Enable dropping of IP fragments.
Possible values: ENABLED, DISABLED Default value: DISABLED
AclLogTime Parameter to tune acl logging time Default value: 5000 Minimum value: 0
implicitACLAllow Do not apply ACLs for internal ports
Possible values: ENABLED, DISABLED Default value: ENABLED
dynamicRouting Enable/Disable Dynamic routing on partition. This configuration is not applicable to default partition
Possible values: ENABLED, DISABLED Default value: DISABLED
ipv6DynamicRouting Enable/Disable IPv6 Dynamic routing
Possible values: ENABLED, DISABLED Default value: DISABLED
allowClassEIPv4 Enable/Disable IPv4 Class E address clients
Possible values: ENABLED, DISABLED Default value: DISABLED
implicitPBR Enable/Disable Policy Based Routing for control packets
Possible values: ENABLED, DISABLED Default value: DISABLED
Related Commands
unset L3Param
Use this command to remove L3Param settings.Refer to the set L3Param command for meanings of the arguments.
Synopsis
unset L3Param [-srcnat] [-icmpGenRateThreshold] [-overrideRnat] [-dropDFFlag] [-mipRoundRobin] [-externalLoopBack] [-tnlPmtuWoConn] [-usipServerStrayPkt] [-forwardICMPFragments] [-dropIPFragments] [-AclLogTime] [-implicitACLAllow] [-dynamicRouting] [-ipv6DynamicRouting] [-allowClassEIPv4] [-implicitPBR]
Share
Share
In this article
This Preview product documentation is Citrix Confidential.
You agree to hold this documentation confidential pursuant to the terms of your Citrix Beta/Tech Preview Agreement.
The development, release and timing of any features or functionality described in the Preview documentation remains at our sole discretion and are subject to change without notice or consultation.
The documentation is for informational purposes only and is not a commitment, promise or legal obligation to deliver any material, code or functionality and should not be relied upon in making Citrix product purchase decisions.
If you do not agree, select I DO NOT AGREE to exit.