Citrix ADC 12.1 NITRO API Reference

INTF ERRORS

August 17, 2023

Contributed by:

INTF ERRORS

Error Code	Error Code(Decimal)	Error Code(Hex)	Error Message
NSERR_1GSFPSPEEDLIMIT	3968	0xf80	1G SFPs are restricted to speed 1000 or AUTO only
NSERR_1GSFPDUPLEXLIMIT	3969	0xf81	1G SFPs are restricted to duplex FULL or AUTO only
NSERR_1GSPEEDLIMIT	3970	0xf82	1G port can not be configured as 10G speed
NSERR_1GDUPLEXLIMIT	3971	0xf83	1G port can not be configured as HALF duplex
NSERR_10GSPEEDLIMIT	3972	0xf84	10G ports on this platform can only be configured as speed 1G, 10G or AUTO only
NSERR_10GDUPLEXLIMIT	3973	0xf85	10G ports on this platform can only be configured as duplex FULL or AUTO only
NSERR_10GAUTONEGLIMIT	3974	0xf86	10G ports on this platform do not support AUTONEG
NSERR_10GSPEEDONLY	3975	0xf87	10G ports on this platform are restricted to speed 10000 or AUTO only
NSERR_FULLDUPLEXONLY	3976	0xf88	These ports do not support HALF duplex mode
NSERR_AUTOINVALSPEED	3977	0xf89	Static CLAG does not support speed as AUTO
NSERR_CLAGSPEEDREQ	3978	0xf8a	Static CLAG explicitly requires speed to be configured other than AUTO
NSERR_THROUGHPUTLIMIT	3979	0xf8b	Throughput limit error. Possible values: 1G port - 1000Mbps, 10G port - 10000Mbps, 40G port - 40000Mbps, Link Aggregation - 80000Mbps
NSERR_BANDWIDTHLIMIT	3980	0xf8c	Bandwidth limit error. Possible values: 1G port - 1000Mbps, 10G port - 10000Mbps, 40G port - 40000Mbps, Link Aggregation - 80000Mbps
NSERR_10GDAC_SPEEDLIMIT	3981	0xf8d	DAC port speed must be configured as 10G or AUTO
NSERR_VIF_LACP_CAUTION	3982	0xf8e	Ensure that the physical interface is not shared with any other VMs.
NSERR_LA_SLAVE_LIMIT	3983	0xf8f	Trying to bind more interfaces than allowed limit
NSERR_SLAVE_MTU_MISMATCH	3987	0xf93	Interface MTU should be same as Channel MTU.
NSERR_BKPLANE_MTU_MISMATCH	3988	0xf94	Interface MTU should be default or same as Backplane MTU.
NSERR_MTU_NOTALLOWED	3989	0xf95	MTU change is not allowed on this interface.
NSERR_BACKPLANE_MTU_LIMIT	3990	0xf96	Backplane Interface, Minimum user configured value for MTU is 1579.
NSERR_INTERFACE_SLAVE_MTU_LIMIT	3991	0xf97	Interface is a part of channel, MTU change is not allowed.
NSERR_CHANNEL_RESTRICT	447	0x1BF	LA channel configuration on VPX running on SDX should be done only from Service VM
NSERR_PTP_CLUS_L3	3992	0xf98	Cluster INC Mode Enabled, PTP state change is not allowed.
NSERR_40GDUPLEXLIMIT	3993	0xf99	40G ports on this platform can only be configured as duplex FULL or AUTO only
NSERR_40GSPEEDONLY	3994	0xf9a	40G ports on this platform are restricted to speed 40000 or AUTO only
NSERR_LRSET_FC_NOT_ALLOWED	3996	0xf9c	Flow Controle settings not allowed for link redundant set interface
NSERR_LRSET_LACP_SET_NOT_ALLOWED	3997	0xf9d	Dynamic LA(LACP) settings are not allowed for link redundant set interface
NSERR_LRSET_LLDPSET_NOT_ALLOWED	3998	0xf9e	LLDP settings are not allowed for link redundant set interface
NSERR_LRSET_SPEED_NOT_ALLOWED	3999	0xf9f	speed setting not allowed for link redundant set interface
NSERR_LRSET_PRIORITY_NOT_ALLOWED	4026	0xfba	lrset priority not allowed for link redundant set master interface
NSERR_LRSET_THROUGHPUT_NOT_ALLOWED	4027	0xfbb	throughput setting not allowed for link redundant set master interface
NSERR_LRSET_BW_SET_NOT_ALLOWED	4028	0xfbc	Bandwidth settings are not allowed for link redundant set interface
NSERR_LRSET_LAG_TYPE_NOT_ALLOWED	4029	0xfbd	Lagtype setting not allowed for link redundant set interface
NSERR_LRSET_DUPLEX_NOT_ALLOWED	4030	0xfbe	Duplex setting not allowed for link redundant set interface
NSERR_LRSET_AUTO_NEG_NOT_ALLOWED	4031	0xfbf	Disabling autonegotiation not allowed for link redundant set interface
NSERR_JF_ESX_VERSION_SUPPORT	4070	0xfe6	Jumbo Frames are supported on ESX 5.5 version and onward
NSERR_TP_SETTINGS_NOT_ALLOWED	3385	0xd39	Trunk Port settings on this interface is not supported
NSERR_LACP_SETTINGS_ON_TP_NOT_ALLOWED	3386	0xd3a	LACP settings on Trunk Port is not allowed
NSERR_IP6_ADDRESS_SETTING_FAILED	3387	0xd3b	IPv6 Address can not be added because MTA table got exhausted
NSERR_50GSPEEDLIMIT	3388	0xd3c	50G ports on this platform can only be configured as speed 10G, 25G, 40G, 50G or AUTO
NSERR_100GSPEEDLIMIT	3389	0xd3d	100G ports on this platform can only be configured as speed 10G, 25G, 40G, 50G, 100G or AUTO

The official version of this content is in English. Some of the Cloud Software Group documentation content is machine translated for your convenience only. Cloud Software Group has no control over machine-translated content, which may contain errors, inaccuracies or unsuitable language. No warranty of any kind, either expressed or implied, is made as to the accuracy, reliability, suitability, or correctness of any translations made from the English original into any other language, or that your Cloud Software Group product or service conforms to any machine translated content, and any warranty provided under the applicable end user license agreement or terms of service, or any other agreement with Cloud Software Group, that the product or service conforms with any documentation shall not apply to the extent that such documentation has been machine translated. Cloud Software Group will not be held responsible for any damage or issues that may arise from using machine-translated content.

Was this helpful

INTF ERRORS

August 17, 2023

Contributed by:

August 17, 2023

Contributed by:

INTF ERRORS

INTF ERRORS

In this article