ADC NITRO APIs

lldpneighbors

May 23, 2024

Contributed by:

Configuration for lldp neighbors resource.

Properties

(click to see Operations )

Name	Permissions	Description
ifnum	Read-write	Interface Name.
nodeid	Read-write	Unique number that identifies the cluster node. Minimum value = 0 Maximum value = 31
chassisidsubtype	Read-only	Chassis id sub type. Possible values = NONE, Component, Interface Alias, Port Component, MAC Address, Network Address, Interface Name, Locally Assigned
chassisid	Read-only	Chassis Id.
portidsubtype	Read-only	Port id subtype. Possible values = NONE, Interface Alias, Port Component, MAC Address, Network Address, Interface Name, Agent Circuit ID, Locally Assigned
portid	Read-only	Port Id.
ttl	Read-only	Time to Live.
portdescription	Read-only	Port Description.
sys	Read-only	System Name.
sysdesc	Read-only	System Description.
mgmtaddresssubtype	Read-only	Management Address Type. Possible values = OTHER, IPv4, IPv6
mgmtaddress	Read-only	Management Address.
iftype	Read-only	Interface subtype. Possible values = UNKNOWN, ifIndex, system port number
ifnumber	Read-only	Interface Number.
vlan	Read-only	vlan name.
vlanid	Read-only	Vlan Id.
portprotosupported	Read-only	Flag to show Port Protocol Support.
portprotoenabled	Read-only	Flag to show Port Protocol support enabled.
portprotoid	Read-only	Port Protocol ID.
portvlanid	Read-only	Port Vlan Id.
protocolid	Read-only	port vlan id name.
linkaggrcapable	Read-only	Is neighbor Link Aggregation Capable. Possible values = NO, YES
linkaggrenabled	Read-only	Is link aggregation Enabled. Possible values = NO, YES
linkaggrid	Read-only	Link Aggregation Id.
flag	Read-only	.
syscapabilities	Read-only	Acronyms for remote system capabilities OT : Other. RE : Repeater(IETF RFC 2108). BR : MAC Bridge(IEEE Std 802.1D). WL : WLAN Access Point(IEEE Std 802.11 MIB). RO : ROuter(IETF RFC 1812). TE : Telephone(IETF RFC 4293). DO : DOCSIS cable device(IETF RFC 4639 and IETF RFC 4546). ST : STation only(IETF RFC 4293). CV : C-VLAN component of a VLAN Bridge(IEEE Std 802.1Q). SV : S-VLAN component of a VLAN Bridge(IEEE Std 802.1Q). MR : Two port MAC Relay(IEEE Std 802.1Q).
syscapenabled	Read-only	Acronyms for remote system enabled capabilities OT : Other. RE : Repeater(IETF RFC 2108). BR : MAC Bridge(IEEE Std 802.1D). WL : WLAN Access Point(IEEE Std 802.11 MIB). RO : ROuter(IETF RFC 1812). TE : Telephone(IETF RFC 4293). DO : DOCSIS cable device(IETF RFC 4639 and IETF RFC 4546). ST : STation only(IETF RFC 4293). CV : C-VLAN component of a VLAN Bridge(IEEE Std 802.1Q). SV : S-VLAN component of a VLAN Bridge(IEEE Std 802.1Q). MR : Two port MAC Relay(IEEE Std 802.1Q).
autonegsupport	Read-only	MAC/PHY autonegotiation support. Possible values = NO, YES
autonegenabled	Read-only	MAC/PHY autonegotiation enabled. Possible values = NO, YES
autonegadvertised	Read-only	MAC/PHY autonegotiation advetised.
autonegmautype	Read-only	MAC/PHY Medium Attachment Unit (MAU) type of the port. Description listed below AUI - no internal MAU, view from AUI 10Base5 - thick coax MAU Foirl - FOIRL MAU 10Base2 - thin coax MAU 10BaseT - UTP MAU 10BaseFP - passive fiber MAU 10BaseFB - sync fiber MAU 10BaseFL - async fiber MAU 10Broad36 - broadband DTE MAU 10BaseTHD - UTP MAU, half duplex mode 10BaseTFD - UTP MAU, full duplex mode 10BaseFLHD - async fiber MAU, half duplex mode 10BaseFLDF - async fiber MAU, full duplex mode 10BaseT4 - 4 pair category 3 UTP 100BaseTXHD - 2 pair category 5 UTP, half duplex mode 100BaseTXFD - 2 pair category 5 UTP, full duplex mode 100BaseFXHD - X fiber over PMT, half duplex mode 100BaseFXFD - X fiber over PMT, full duplex mode 100BaseT2HD - 2 pair category 3 UTP, half duplex mode 100BaseT2DF - 2 pair category 3 UTP, full duplex mode 1000BaseXHD - PCS/PMA, unknown PMD, half duplex mode 1000BaseXFD - PCS/PMA, unknown PMD, full duplex mode 1000BaseLXHD - Fiber over long-wavelength laser, half duplex mode 1000BaseLXFD - Fiber over long-wavelength laser, full duplex mode 1000BaseSXHD - Fiber over short-wavelength laser, half duplex mode 1000BaseSXFD - Fiber over short-wavelength laser, full duplex mode 1000BaseCXHD - Copper over 150-Ohm balanced cable, half duplex mode 1000BaseCXFD - Copper over 150-Ohm balanced cable, full duplex mode 1000BaseTHD - Four-pair Category 5 UTP, half duplex mode 1000BaseTFD - Four-pair Category 5 UTP, full duplex mode 10GigBaseX - X PCS/PMA, unknown PMD 10GigBaseLX4 - X fiber over WWDM optics 10GigBaseR - R PCS/PMA, unknown PMD 10GigBaseER - R fiber over 1550 nm optics 10GigBaseLR - R fiber over 1310 nm optics 10GigBaseSR - R fiber over 850 nm optics 10GigBaseW - W PCS/PMA, unknown PMD 10GigBaseEW - W fiber over 1550 nm optics 10GigBaseLW - W fiber over 1310 nm optics 10GigBaseSW - W fiber over 850 nm optics. Possible values = Not Recieved, AUI, 10Base5, Foirl, 10Base2, 10BaseT, 10BaseFP, 10BaseFB, 10BaseFL, 10Broad36, 10BaseTHD, 10BaseTFD, 10BaseFLHD, 10BaseFLDF, 10BaseT4, 100BaseTXHD, 100BaseTXFD, 100BaseFXHD, 100BaseFXFD, 100BaseT2HD, 100BaseT2DF, 1000BaseXHD, 1000BaseXFD, 1000BaseLXHD, 1000BaseLXFD, 1000BaseSXHD, 1000BaseSXFD, 1000BaseCXHD, 1000BaseCXFD, 1000BaseTHD, 1000BaseTFD, 10GigBaseX, 10GigBaseLX4, 10GigBaseR, 10GigBaseER, 10GigBaseLR, 10GigBaseSR, 10GigBaseW, 10GigBaseEW, 10GigBaseLW, 10GigBaseSW
mtu	Read-only	MTU of Remote Device.
__count	Read-only	count parameter

Operations

(click to see Properties )

GET (ALL)
GET
COUNT
CLEAR

Some options that you can use for each operations:

Getting warnings in response: NITRO allows you to get warnings in an operation by specifying the 'warning' query parameter as 'yes'. For example, to get warnings while connecting to the NetScaler appliance, the URL is as follows:

http:// <netscaler-ip-address> /nitro/v1/config/login?warning=yes

If any, the warnings are displayed in the response payload with the HTTP code '209 X-NITRO-WARNING'.
Authenticated access for individual NITRO operations: NITRO allows you to logon to the NetScaler appliance to perform individual operations. You can use this option instead of creating a NITRO session (using the login object) and then using that session to perform all operations,

To do this, you must specify the username and password in the request header of the NITRO request as follows:

X-NITRO-USER: <username>

X-NITRO-PASS: <password>

Note: In such cases, make sure that the request header DOES not include the following:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

*Note:* Mandatory parameters are marked in red and placeholder content is marked in green

clear

URL: http:// <netscaler-ip-address> /nitro/v1/config/lldpneighbors? action=clear HTTP Method: POST

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Content-Type:application/json

Request Payload:

{"lldpneighbors":{
}}

<!--NeedCopy-->

Response: HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

get (all)

URL: http:// <netscaler-ip-address> /nitro/v1/config/lldpneighbors Query-parameters: args http:// <netscaler-ip-address> /nitro/v1/config/lldpneighbors? args=ifnum: <String_value> ,nodeid: <Double_value>

Use this query-parameter to get lldpneighbors resources based on additional properties.

attrs http:// <netscaler-ip-address> /nitro/v1/config/lldpneighbors? attrs=property-name1,property-name2

Use this query parameter to specify the resource details that you want to retrieve.

filter http:// <netscaler-ip-address> /nitro/v1/config/lldpneighbors? filter=property-name1:property-val1,property-name2:property-val2

Use this query-parameter to get the filtered set of lldpneighbors resources configured on NetScaler.Filtering can be done on any of the properties of the resource.

view http:// <netscaler-ip-address> /nitro/v1/config/lldpneighbors? view=summary

Use this query-parameter to get the summary output of lldpneighbors resources configured on NetScaler.

Note: By default, the retrieved results are displayed in detail view (?view=detail).

pagination http:// <netscaler-ip-address> /nitro/v1/config/lldpneighbors? pagesize=#no;pageno=#no

Use this query-parameter to get the lldpneighbors resources in chunks.

HTTP Method: GET

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Accept:application/json

Response: HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

Response Header:

Content-Type:application/json

Response Payload:

{ "lldpneighbors": [ {
ifnum:<String_value>,nodeid:<Double_value>"chassisidsubtype":<String_value>,
"chassisid":<String_value>,
"portidsubtype":<String_value>,
"portid":<String_value>,
"ttl":<Double_value>,
"portdescription":<String_value>,
"sys":<String_value>,
"sysdesc":<String_value>,
"mgmtaddresssubtype":<String_value>,
"mgmtaddress":<String_value>,
"iftype":<String_value>,
"ifnumber":<Double_value>,
"vlan":<String_value>,
"vlanid":<Double_value>,
"portprotosupported":<Double_value>,
"portprotoenabled":<Double_value>,
"portprotoid":<Double_value>,
"portvlanid":<Double_value>,
"protocolid":<String_value>,
"linkaggrcapable":<String_value>,
"linkaggrenabled":<String_value>,
"linkaggrid":<Double_value>,
"flag":<Double_value>,
"syscapabilities":<String_value>,
"syscapenabled":<String_value>,
"autonegsupport":<String_value>,
"autonegenabled":<String_value>,
"autonegadvertised":<String_value>,
"autonegmautype":<String_value>,
"mtu":<Double_value>
}]}

<!--NeedCopy-->

get

URL: http:// <netscaler-ip-address> /nitro/v1/config/lldpneighbors/ ifnum_value<String> Query-parameters: attrs http:// <netscaler-ip-address> /nitro/v1/config/lldpneighbors/ ifnum_value<String> ? attrs=property-name1,property-name2

Use this query parameter to specify the resource details that you want to retrieve.

view http:// <netscaler-ip-address> /nitro/v1/config/lldpneighbors/ ifnum_value<String> ? view=summary

Use this query-parameter to get the summary output of lldpneighbors resources configured on NetScaler.

Note: By default, the retrieved results are displayed in detail view (?view=detail).

HTTP Method: GET

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Accept:application/json

Response: HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

Response Header:

Content-Type:application/json

Response Payload:

{  "lldpneighbors": [ {
ifnum:<String_value>,nodeid:<Double_value>"chassisidsubtype":<String_value>,
"chassisid":<String_value>,
"portidsubtype":<String_value>,
"portid":<String_value>,
"ttl":<Double_value>,
"portdescription":<String_value>,
"sys":<String_value>,
"sysdesc":<String_value>,
"mgmtaddresssubtype":<String_value>,
"mgmtaddress":<String_value>,
"iftype":<String_value>,
"ifnumber":<Double_value>,
"vlan":<String_value>,
"vlanid":<Double_value>,
"portprotosupported":<Double_value>,
"portprotoenabled":<Double_value>,
"portprotoid":<Double_value>,
"portvlanid":<Double_value>,
"protocolid":<String_value>,
"linkaggrcapable":<String_value>,
"linkaggrenabled":<String_value>,
"linkaggrid":<Double_value>,
"flag":<Double_value>,
"syscapabilities":<String_value>,
"syscapenabled":<String_value>,
"autonegsupport":<String_value>,
"autonegenabled":<String_value>,
"autonegadvertised":<String_value>,
"autonegmautype":<String_value>,
"mtu":<Double_value>
}]}

<!--NeedCopy-->

count

URL: http:// <netscaler-ip-address> /nitro/v1/config/lldpneighbors? count=yes HTTP Method: GET

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Accept:application/json

Response: HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

Response Header:

Content-Type:application/json

Response Payload:

{ "lldpneighbors": [ { "__count": "#no"} ] }

<!--NeedCopy-->

The official version of this content is in English. Some of the Cloud Software Group documentation content is machine translated for your convenience only. Cloud Software Group has no control over machine-translated content, which may contain errors, inaccuracies or unsuitable language. No warranty of any kind, either expressed or implied, is made as to the accuracy, reliability, suitability, or correctness of any translations made from the English original into any other language, or that your Cloud Software Group product or service conforms to any machine translated content, and any warranty provided under the applicable end user license agreement or terms of service, or any other agreement with Cloud Software Group, that the product or service conforms with any documentation shall not apply to the extent that such documentation has been machine translated. Cloud Software Group will not be held responsible for any damage or issues that may arise from using machine-translated content.

Was this helpful

lldpneighbors

May 23, 2024

Contributed by:

May 23, 2024

Contributed by:

lldpneighbors

Properties

Operations

clear

get (all)

get

count

In this article