Developer Documentation
ADC NITRO APIs
Current Release 13.1 13

vrid6

May 23, 2024
Contributed by: 
C

Configuration for Virtual Router ID for IPv6 resource.

Properties

(click to see Operations )

Name Data Type Permissions Description
id Read-write Integer value that uniquely identifies a VMAC6 address.

Minimum value = 1

Maximum value = 255
priority Read-write Base priority (BP), in an active-active mode configuration, which ordinarily determines the master VIP address.

Default value: 255

Minimum value = 0

Maximum value = 255
preemption Read-write In an active-active mode configuration, make a backup VIP address the master if its priority becomes higher than that of a master VIP address bound to this VMAC address.

If you disable pre-emption while a backup VIP address is the master, the backup VIP address remains master until the original master VIP’s priority becomes higher than that of the current master.

Default value: ENABLED

Possible values = ENABLED, DISABLED
sharing Read-write In an active-active mode configuration, enable the backup VIP address to process any traffic instead of dropping it.

Default value: DISABLED

Possible values = ENABLED, DISABLED
tracking Read-write The effective priority (EP) value, relative to the base priority (BP) value in an active-active mode configuration. When EP is set to a value other than None, it is EP, not BP, which determines the master VIP address. Available settings function as follows
  • NONE - No tracking. EP = BP
  • ALL - If the status of all virtual servers is UP, EP = BP. Otherwise, EP = 0.
  • ONE - If the status of at least one virtual server is UP, EP = BP. Otherwise, EP = 0.
  • PROGRESSIVE - If the status of all virtual servers is UP, EP = BP. If the status of all virtual servers is DOWN, EP = 0. Otherwise EP = BP (1 - K/N), where N is the total number of virtual servers associated with the VIP address and K is the number of virtual servers for which the status is DOWN. Default: NONE. Default value: NONE Possible values = NONE, ONE, ALL, PROGRESSIVE
    		•
    preemptiondelaytimer Read-write Preemption delay time in seconds, in an active-active configuration. If any high priority node will come in network, it will wait for these many seconds before becoming master.

    Default value: 0

    Minimum value = 1

    Maximum value = 36000
    trackifnumpriority Read-write Priority by which the Effective priority will be reduced if any of the tracked interfaces goes down in an active-active configuration.

    Default value: 0

    Minimum value = 1

    Maximum value = 255
    ownernode Read-write In a cluster setup, assign a cluster node as the owner of this VMAC address for IP based VRRP configuration. If no owner is configured, ow ner node is displayed as ALL and one node is dynamically elected as the owner.

    Minimum value = 0

    Maximum value = 31
    all Read-write Remove all configured VMAC6 addresses from the Citrix ADC.
    ifaces Read-only Interfaces bound to this VRID.
    ifnum Read-only Interfaces to bind to the VMAC6, specified in (slot/port) notation (for example, 1/2).Use spaces to separate multiple entries.
    type Read-only Type (static or dynamic) of this VRID.

    Possible values = STATIC, DYNAMIC
    state Read-only State of this VRID.
    flags Read-only Flags.
    ipaddress Read-only The IP address bound to the VRID6.
    effectivepriority Read-only The effective priority of this VRID.
    operationalownernode Read-only Run time owner node of the vrid.

    Minimum value = 0

    Maximum value = 31
    __count Read-only count parameter

    Operations

    (click to see Properties )

    • ADD
    • DELETE
    • UPDATE
    • UNSET
    • GET (ALL)
    • GET
    • COUNT

    Some options that you can use for each operations:

    • Getting warnings in response: NITRO allows you to get warnings in an operation by specifying the 'warning' query parameter as 'yes'. For example, to get warnings while connecting to the NetScaler appliance, the URL is as follows:

      http:// <netscaler-ip-address> /nitro/v1/config/login?warning=yes

      If any, the warnings are displayed in the response payload with the HTTP code '209 X-NITRO-WARNING'.

    • Authenticated access for individual NITRO operations: NITRO allows you to logon to the NetScaler appliance to perform individual operations. You can use this option instead of creating a NITRO session (using the login object) and then using that session to perform all operations,

      To do this, you must specify the username and password in the request header of the NITRO request as follows:

      X-NITRO-USER: <username>

      X-NITRO-PASS: <password>

      Note: In such cases, make sure that the request header DOES not include the following:

      Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

    *Note: * Mandatory parameters are marked in red and placeholder content is marked in green

    add

    URL: http:// <netscaler-ip-address> /nitro/v1/config/vrid6 HTTP Method: POST

    Request Headers:

    Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

    Content-Type:application/json

    Request Payload: 

    {"vrid6":{
<b>"id":<Double_value>,
</b>"priority":<Double_value>,
"preemption":<String_value>,
"sharing":<String_value>,
"tracking":<String_value>,
"preemptiondelaytimer":<Double_value>,
"trackifnumpriority":<Double_value>,
"ownernode":<Double_value>
}}

<!--NeedCopy-->

    Response: HTTP Status Code on Success: 201 Created

    HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

    delete

    URL: http:// <netscaler-ip-address> /nitro/v1/config/vrid6/ id_value<Double> Query-parameters: args=all: <Boolean_value>

    </b>

    HTTP Method: DELETE

    Request Headers:

    Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

    Response: HTTP Status Code on Success: 200 OK

    HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

    update

    URL: http:// <netscaler-ip-address> /nitro/v1/config/vrid6 HTTP Method: PUT

    Request Headers:

    Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

    Content-Type:application/json

    Request Payload: 

    {"vrid6":{
<b>"id":<Double_value>,
</b>"priority":<Double_value>,
"preemption":<String_value>,
"sharing":<String_value>,
"tracking":<String_value>,
"preemptiondelaytimer":<Double_value>,
"trackifnumpriority":<Double_value>,
"ownernode":<Double_value>
}}

<!--NeedCopy-->

    Response: HTTP Status Code on Success: 200 OK

    HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

    unset

    URL: http:// <netscaler-ip-address> /nitro/v1/config/vrid6? action=unset HTTP Method: POST

    Request Headers:

    Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

    Content-Type:application/json

    Request Payload: 

    {"vrid6":{
<b>"id":<Double_value>,
</b>"priority":true,
"preemption":true,
"sharing":true,
"tracking":true,
"preemptiondelaytimer":true,
"trackifnumpriority":true,
"ownernode":true
}}

<!--NeedCopy-->

    Response: HTTP Status Code on Success: 200 OK

    HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

    get (all)

    URL: http:// <netscaler-ip-address> /nitro/v1/config/vrid6 Query-parameters: attrs http:// <netscaler-ip-address> /nitro/v1/config/vrid6? attrs=property-name1,property-name2

    Use this query parameter to specify the resource details that you want to retrieve.

    filter http:// <netscaler-ip-address> /nitro/v1/config/vrid6? filter=property-name1:property-val1,property-name2:property-val2

    Use this query-parameter to get the filtered set of vrid6 resources configured on NetScaler.Filtering can be done on any of the properties of the resource.

    view http:// <netscaler-ip-address> /nitro/v1/config/vrid6? view=summary

    Use this query-parameter to get the summary output of vrid6 resources configured on NetScaler.

    Note: By default, the retrieved results are displayed in detail view (?view=detail).

    pagination http:// <netscaler-ip-address> /nitro/v1/config/vrid6? pagesize=#no;pageno=#no

    Use this query-parameter to get the vrid6 resources in chunks.

    HTTP Method: GET

    Request Headers:

    Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

    Accept:application/json

    Response: HTTP Status Code on Success: 200 OK

    HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

    Response Header:

    Content-Type:application/json

    Response Payload: 

    { "vrid6": [ {
"id":<Double_value>,
"ifaces":<String_value>,
"ifnum":<String_value>,
"type":<String_value>,
"priority":<Double_value>,
"state":<Double_value>,
"flags":<Double_value>,
"ipaddress":<String_value>,
"preemption":<String_value>,
"sharing":<String_value>,
"preemptiondelaytimer":<Double_value>,
"trackifnumpriority":<Double_value>,
"effectivepriority":<Double_value>,
"tracking":<String_value>,
"operationalownernode":<Double_value>,
"ownernode":<Double_value>
}]}

<!--NeedCopy-->

    get

    URL: http:// <netscaler-ip-address> /nitro/v1/config/vrid6/ id_value<Double> Query-parameters: attrs http:// <netscaler-ip-address> /nitro/v1/config/vrid6/ id_value<Double> ? attrs=property-name1,property-name2

    Use this query parameter to specify the resource details that you want to retrieve.

    view http:// <netscaler-ip-address> /nitro/v1/config/vrid6/ id_value<Double> ? view=summary

    Use this query-parameter to get the summary output of vrid6 resources configured on NetScaler.

    Note: By default, the retrieved results are displayed in detail view (?view=detail).

    HTTP Method: GET

    Request Headers:

    Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

    Accept:application/json

    Response: HTTP Status Code on Success: 200 OK

    HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

    Response Header:

    Content-Type:application/json

    Response Payload: 

    {  "vrid6": [ {
"id":<Double_value>,
"ifaces":<String_value>,
"ifnum":<String_value>,
"type":<String_value>,
"priority":<Double_value>,
"state":<Double_value>,
"flags":<Double_value>,
"ipaddress":<String_value>,
"preemption":<String_value>,
"sharing":<String_value>,
"preemptiondelaytimer":<Double_value>,
"trackifnumpriority":<Double_value>,
"effectivepriority":<Double_value>,
"tracking":<String_value>,
"operationalownernode":<Double_value>,
"ownernode":<Double_value>
}]}

<!--NeedCopy-->

    count

    URL: http:// <netscaler-ip-address> /nitro/v1/config/vrid6? count=yes HTTP Method: GET

    Request Headers:

    Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

    Accept:application/json

    Response: HTTP Status Code on Success: 200 OK

    HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

    Response Header:

    Content-Type:application/json

    Response Payload: 

    { "vrid6": [ { "__count": "#no"} ] }

<!--NeedCopy-->
    vrid6
    May 23, 2024
    Contributed by: 
    C
    May 23, 2024
    Contributed by: 
    C

    In this article

    Site feedback | Your privacy choices footer linkYour Privacy Choices | Privacy and legal terms | Cookie preferences | Consent settings | docs.cloud.com
    © 1999- Cloud Software Group, Inc. All rights reserved.