ADC NITRO APIs

vlan

May 23, 2024

Contributed by:

Configuration for “VLAN” resource.

Properties

(click to see Operations )

Name	Permissions	Description
id	Read-write	A positive integer that uniquely identifies a VLAN. Minimum value = 1 Maximum value = 4094
aliasname	Read-write	A name for the VLAN. Must begin with a letter, a number, or the underscore symbol, and can consist of from 1 to 31 letters, numbers, and the hyphen (-), period (.) pound (#), space ( ), at sign (@), equals (=), colon (:), and underscore (_) characters. You should choose a name that helps identify the VLAN. However, you cannot perform any VLAN operation by specifying this name instead of the VLAN ID. Maximum length = 31
dynamicrouting	Read-write	Enable dynamic routing on this VLAN. Default value: DISABLED Possible values = ENABLED, DISABLED
ipv6dynamicrouting	Read-write	Enable all IPv6 dynamic routing protocols on this VLAN. Note: For the ENABLED setting to work, you must configure IPv6 dynamic routing protocols from the VTYSH command line. Default value: DISABLED Possible values = ENABLED, DISABLED
mtu	Read-write	Specifies the maximum transmission unit (MTU), in bytes. The MTU is the largest packet size, excluding 14 bytes of ethernet header and 4 bytes of crc, that can be transmitted and received over this VLAN. Default value: 0 Minimum value = 500 Maximum value = 9216
sharing	Read-write	If sharing is enabled, then this vlan can be shared across multiple partitions by binding it to all those partitions. If sharing is disabled, then this vlan can be bound to only one of the partitions. Default value: DISABLED Possible values = ENABLED, DISABLED
linklocalipv6addr	Read-only	The link-local IP address assigned to the VLAN.
rnat	Read-only	Temporary flag used for internal purpose.
portbitmap	Read-only	Member interfaces of this vlan.
lsbitmap	Read-only	Member linksets of this vlan.
tagbitmap	Read-only	Tagged members of this vlan.
lstagbitmap	Read-only	Tagged linksets of this vlan.
ifaces	Read-only	Names of all member interfaces of this vlan.
tagifaces	Read-only	Names of all tagged member interfaces of this vlan.
ifnum	Read-only	The interface to be bound to the VLAN, specified in slot/port notation (for example, 1/3). Minimum length = 1
tagged	Read-only	Make the interface an 802.1q tagged interface. Packets sent on this interface on this VLAN have an additional 4-byte 802.1q tag, which identifies the VLAN. To use 802.1q tagging, you must also configure the switch connected to the appliance’s interfaces.
vlantd	Read-only	Traffic domain associated with vlan. Minimum value = 0 Maximum value = 4094
sdxvlan	Read-only	SDX vlan. Default value: NO Possible values = YES, NO
partitionname	Read-only	Name of the Partition to which this vlan bound to. Minimum length = 1
vxlan	Read-only	The VXLAN that extends this vlan.
__count	Read-only	count parameter

Operations

(click to see Properties )

ADD
DELETE
UPDATE
UNSET
GET (ALL)
GET
COUNT

Some options that you can use for each operations:

Getting warnings in response: NITRO allows you to get warnings in an operation by specifying the 'warning' query parameter as 'yes'. For example, to get warnings while connecting to the NetScaler appliance, the URL is as follows:

http:// <netscaler-ip-address> /nitro/v1/config/login?warning=yes

If any, the warnings are displayed in the response payload with the HTTP code '209 X-NITRO-WARNING'.
Authenticated access for individual NITRO operations: NITRO allows you to logon to the NetScaler appliance to perform individual operations. You can use this option instead of creating a NITRO session (using the login object) and then using that session to perform all operations,

To do this, you must specify the username and password in the request header of the NITRO request as follows:

X-NITRO-USER: <username>

X-NITRO-PASS: <password>

Note: In such cases, make sure that the request header DOES not include the following:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

*Note:* Mandatory parameters are marked in red and placeholder content is marked in green

add

URL: http:// <netscaler-ip-address> /nitro/v1/config/vlan HTTP Method: POST

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Content-Type:application/json

Request Payload:

{"vlan":{
<b>"id":<Double_value>,
</b>"aliasname":<String_value>,
"dynamicrouting":<String_value>,
"ipv6dynamicrouting":<String_value>,
"mtu":<Double_value>,
"sharing":<String_value>
}}

<!--NeedCopy-->

Response: HTTP Status Code on Success: 201 Created

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

delete

URL: http:// <netscaler-ip-address> /nitro/v1/config/vlan/ id_value<Double> HTTP Method: DELETE

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Response: HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

update

URL: http:// <netscaler-ip-address> /nitro/v1/config/vlan HTTP Method: PUT

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Content-Type:application/json

Request Payload:

{"vlan":{
<b>"id":<Double_value>,
</b>"aliasname":<String_value>,
"dynamicrouting":<String_value>,
"ipv6dynamicrouting":<String_value>,
"mtu":<Double_value>,
"sharing":<String_value>
}}

<!--NeedCopy-->

Response: HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

unset

URL: http:// <netscaler-ip-address> /nitro/v1/config/vlan? action=unset HTTP Method: POST

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Content-Type:application/json

Request Payload:

{"vlan":{
<b>"id":<Double_value>,
</b>"aliasname":true,
"dynamicrouting":true,
"ipv6dynamicrouting":true,
"mtu":true,
"sharing":true
}}

<!--NeedCopy-->

Response: HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

get (all)

URL: http:// <netscaler-ip-address> /nitro/v1/config/vlan Query-parameters: attrs http:// <netscaler-ip-address> /nitro/v1/config/vlan? attrs=property-name1,property-name2

Use this query parameter to specify the resource details that you want to retrieve.

filter http:// <netscaler-ip-address> /nitro/v1/config/vlan? filter=property-name1:property-val1,property-name2:property-val2

Use this query-parameter to get the filtered set of vlan resources configured on NetScaler.Filtering can be done on any of the properties of the resource.

view http:// <netscaler-ip-address> /nitro/v1/config/vlan? view=summary

Use this query-parameter to get the summary output of vlan resources configured on NetScaler.

Note: By default, the retrieved results are displayed in detail view (?view=detail).

pagination http:// <netscaler-ip-address> /nitro/v1/config/vlan? pagesize=#no;pageno=#no

Use this query-parameter to get the vlan resources in chunks.

HTTP Method: GET

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Accept:application/json

Response: HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

Response Header:

Content-Type:application/json

Response Payload:

{ "vlan": [ {
"id":<Double_value>,
"aliasname":<String_value>,
"linklocalipv6addr":<String_value>,
"rnat":<Boolean_value>,
"portbitmap":<Double_value>,
"lsbitmap":<Double_value>,
"tagbitmap":<Double_value>,
"lstagbitmap":<Double_value>,
"ifaces":<String_value>,
"tagifaces":<String_value>,
"dynamicrouting":<String_value>,
"ipv6dynamicrouting":<String_value>,
"ifnum":<String_value>,
"tagged":<Boolean_value>,
"vlantd":<Double_value>,
"sdxvlan":<String_value>,
"mtu":<Double_value>,
"sharing":<String_value>,
"partitionname":<String_value>,
"vxlan":<Double_value>
}]}

<!--NeedCopy-->

get

URL: http:// <netscaler-ip-address> /nitro/v1/config/vlan/ id_value<Double> Query-parameters: attrs http:// <netscaler-ip-address> /nitro/v1/config/vlan/ id_value<Double> ? attrs=property-name1,property-name2

Use this query parameter to specify the resource details that you want to retrieve.

view http:// <netscaler-ip-address> /nitro/v1/config/vlan/ id_value<Double> ? view=summary

Use this query-parameter to get the summary output of vlan resources configured on NetScaler.

Note: By default, the retrieved results are displayed in detail view (?view=detail).

HTTP Method: GET

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Accept:application/json

Response: HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

Response Header:

Content-Type:application/json

Response Payload:

{  "vlan": [ {
"id":<Double_value>,
"aliasname":<String_value>,
"linklocalipv6addr":<String_value>,
"rnat":<Boolean_value>,
"portbitmap":<Double_value>,
"lsbitmap":<Double_value>,
"tagbitmap":<Double_value>,
"lstagbitmap":<Double_value>,
"ifaces":<String_value>,
"tagifaces":<String_value>,
"dynamicrouting":<String_value>,
"ipv6dynamicrouting":<String_value>,
"ifnum":<String_value>,
"tagged":<Boolean_value>,
"vlantd":<Double_value>,
"sdxvlan":<String_value>,
"mtu":<Double_value>,
"sharing":<String_value>,
"partitionname":<String_value>,
"vxlan":<Double_value>
}]}

<!--NeedCopy-->

count

URL: http:// <netscaler-ip-address> /nitro/v1/config/vlan? count=yes HTTP Method: GET

Request Headers:

Cookie:NITRO_AUTH_TOKEN= <tokenvalue>

Accept:application/json

Response: HTTP Status Code on Success: 200 OK

HTTP Status Code on Failure: 4xx <string> (for general HTTP errors) or 5xx <string> (for NetScaler-specific errors). The response payload provides details of the error

Response Header:

Content-Type:application/json

Response Payload:

{ "vlan": [ { "__count": "#no"} ] }

<!--NeedCopy-->

The official version of this content is in English. Some of the Cloud Software Group documentation content is machine translated for your convenience only. Cloud Software Group has no control over machine-translated content, which may contain errors, inaccuracies or unsuitable language. No warranty of any kind, either expressed or implied, is made as to the accuracy, reliability, suitability, or correctness of any translations made from the English original into any other language, or that your Cloud Software Group product or service conforms to any machine translated content, and any warranty provided under the applicable end user license agreement or terms of service, or any other agreement with Cloud Software Group, that the product or service conforms with any documentation shall not apply to the extent that such documentation has been machine translated. Cloud Software Group will not be held responsible for any damage or issues that may arise from using machine-translated content.

Was this helpful

vlan

May 23, 2024

Contributed by:

May 23, 2024

Contributed by:

vlan

Properties

Operations

add

delete

update

unset

get (all)

get

count

In this article